Žemagrindė puspriekabė

FAYMONVILLE Multimax Satteltieflader (2+2) - nachlaufgelenkt

You can find our complete vehicle inventory, including immediately and short-term available units, on our website.

Excerpt of Features. Full equipment list available upon request.

GOOSENECK:
* Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm in length, with rear bevel approx. 1,000 mm x 10°
* For tractor units: 4 x 2, 6 x 2, and 6 x 4
* Plug-in steel bulkhead, approx. 400 mm high
* ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets
* 3 kW electro-hydraulic power unit for hydraulic operations (excluding hydraulic winches)
* Gooseneck outer beam with fixture boreholes for screw-in lashing rings
* One mounting hole in the upper rear area of the gooseneck outer beam for a screw-in lashing ring
* 1 pair of screw-in lashing rings included (LC 10,000 daN)
* On the gooseneck: 1 pair of plug-in anodized aluminum side walls, approx. 400 mm high
* On the gooseneck: 1 plug-in anodized aluminum rear wall, approx. 400 mm high
* Heavy-duty hardwood flooring, approx. 40 mm over the gooseneck
* 2-inch kingpin
* 1 crosswise stake pocket rail in the gooseneck floor in front of the bevel, for plug-in stakes approx. 100 x 50 mm

LOADING PLATFORM:
* Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10°
* Recess in the loading platform, extending into the bevel, for excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H)
* TPMS tire pressure monitoring system per ECE R 141
* BPW axles and suspension, 1st and 2nd axles fixed, 3rd and 4th axles steered
* 3rd and 4th axles with electromagnetic reverse lock, activated via reverse gear and manually
* Axle load capacity: 12,000 kg each, air suspension with raise/lower valve
* Mechanical landing legs with 2-speed gearbox and crank
* Hardwood flooring, approx. 50 mm thick, continuous and interrupted between axles (increases friction coefficient)
* 1 intermediate table with recessed platform, approx. 300 mm wide, for the large-diameter extension tube with steel treadplate
* 1 pair of lashing rings on the front cross-member (LC 10,000 daN)
* 6 pairs of recessed, fold-out lashing rings in the outer frame (LC 10,000 daN)
* Additional 1 pair of external lashing rings on the front cross-member, rotated approx. 90° towards the loading platform (LC 10,000 daN)
* Extendable (galvanized) width extensions approx. 230 mm per side (without wood planks)
* 1 pair of permanently installed open wheel recesses up to the extension, approx. 700 x 410 mm (W x D), in the deck ahead of the 1st axle
* Between 2nd and 3rd axles, 1 pair of fixed wheel recesses approx. 1,695 x 700 x 410 mm (L x W x D)
* 1 pair mechanical rear supports
* 245/70 R 17.5 3PMSF twin tires – manufacturer of our choice

HYDRAULIC LOADING RAMPS:
* DR-15/60-900-4350-HB-HV-M
* One pair of two-section steel ramps, approx. 4,350 mm long and 900 mm wide
* Hardwood-covered hydraulically foldable ramp ends
* Each ramp hydraulically adjustable approx. 235 mm outwards and 215 mm inwards
* Hardwood decking on loading platform bevel
* Ramps with hardwood overlay

BRAKE SYSTEM:
Csdpfxsyhkrle Afijgn
* WABCO EBS-E brake system compliant with EU regulations

SURFACE TREATMENT:
* HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% a...

Skelbimas verčiamas automatiškai, todėl jame gali būtų vertimo klaidų.