Atvira puspriekabė su tentu

KRONE SDP 27*Mega*BPW*LiftA*StaplerH

Volume semi-trailer
Distance from kingpin to center of support device: 2,267 mm
Fifth wheel height unladen: 980 mm
Double T-shaped longitudinal and center beams, as well as
crossmembers and outriggers, welded together
Outer frame with
Multilock outer frame, universal load securing options every 100 mm
Front height: 80 mm (incl. floor and fifth wheel plate)
2" kingpin (corner dimension: 2,040 mm)
Rear underrun protection device according to EC directive,
for cargo area length: 13,620 mm i.L.
for cargo area width 2,480 mm i.L.
3 axles, each with 9,000 kg load-bearing capacity
Aggregate distance = 7,900 mm
Wheelbase: 1,310 / 1,310 mm
with center centering
BPW axles, 19.5", with air suspension (total travel 260 mm)
and disc brake (ET 120)
Brake disc with 370 mm diameter
Tire size: 6-ply, 435/50 R 19.5
Tread depths:
5/4 mm
4/12 mm
9/6 mm
with lifting and lowering system, including automatic
vehicle height adjustment
load-dependent, fully automatic electronic
lift axle control for 1st axle
manual function on control console for forced lifting
(= starting aid acc. to Directive 97/27/EC) and forced lowering
Preparation of the lift/trailing axle(s) for operation
Njdpfxjzr Dkzj Agljdb
from the tractor unit (without tractor unit installation),
according to the selected connector(s) for light,
for control via
Note: The vehicle does not operate in
the BO power circuit with the 1st axle lifted! The lift axle may only be used as a starting aid according to
Directive 97/27/EC!
Caution: reduced ground clearance in the area of the lift axle!
Through-loading height restricted by pallet stop
Cargo area width in the area of the pallet stop
reduced to: 2,460 mm i.L.
Supply and installation of a rear forklift bracket, suitable
for Palfinger piggyback forklifts (incl. forklift pockets, underrun protection according to ECE-R58 and 2 support brackets for securing chains on the outside)
Tire size of piggyback forklift max.: 23"
Design of the mounting bracket: spar bracket
Dimensions of the support spars: 100 x 100 x 10 x 1500 mm
Dimensions of the forklift pockets: 200x100x5x1200 mm
Center distance of the forklift pockets: 380 mm
Width of the folded-down underrun protection: 1340 mm
Forklift pockets are flush with the rear crossmember.
Socket at the rear: 15-pole DIN ISO 12098
uneven load distribution!
Type: BO 13620
30 mm thick, waterproof floor panel, edge surfaces
sealed all around, continuous, waterproof adhesive
between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to max. 7,000 kg forklift axle load.
Tear plate embedded in the floor panel at the rear (4x450mm)
Type: AB 13620 AGG Dimensions 13,620 mm i.L. x width i.L.
see uprights
LM universal outer spars, continuous, for accommodating
sliding tarpaulin and sliding uprights
Edscha sliding tarpaulin (175) with plastic hinges,
construction height 175 mm, inclination 0 mm, designed for
the transport of pallet boxes according to DIN 15155
Height i.L. lower edge of outer spar laterally in front: 2,860 mm
Height i.L. lower edge of outer spar laterally at the rear: 2,860 mm
Height i.L. lower edge of cross spar in the middle: 3,000 mm
Through-loading height in the rear portal: 2,845 mm
unladen total vehicle height at the highest point approx. 4095 mm
hydraulic roof with 500 mm total lift,
can be raised separately on 4 corner uprights
Construction height at the front from the highest driving height (basic position)
can be lowered by 150 mm (in 50 mm incremen

Skelbimas buvo automatiškai išverstas. Galimos vertimo klaidos.