Atvira puspriekabė su tentu

KRONE SDP 27*Mega*SAF*LiftA*LenkA*StaplerH

VIN: WKESD00000891776

Distance from kingpin to center of support device: 2,267 mm
Fifth wheel height unladen: 980 mm
Double-T longitudinal and center beams as well as
cross beams and outriggers welded together
Outer frame with
Hodpfx Ajzl Nzlefnjnp
Multilock outer frame, universal load securing option every 100 mm
Front height: 80 mm (incl. floor and fifth wheel plate)
2" kingpin (corner dimension: 2,040 mm)
Rear underrun protection device according to EC directive,
for cargo area length: 13,620 mm i.L.
for cargo area width 2,480 mm i.L.
3 axles, each with a load capacity of 9,000 kg
Aggregate distance = 7,900 mm
Wheelbase: 1,310 / 1,310 mm
with center alignment
BPW axles, 19.5", with air suspension (total travel 260 mm)
and disc brake (ET 120)
Brake disc with 370 mm diameter
Tire size 6-fold, 445/45 R 19.5
Tread depths
9/11mm
8/10mm
6/12mm
with lifting and lowering system, incl. automatic
ride height reset
load-dependent, fully automatic electronic
lift axle control for 1st axle
manual function on control console for forced lifting
(= starting aid according to Directive 97/27/EC) and forced lowering
Preparation of the lift/tag axle(s) for operation
from the tractor unit (without tractor unit installation),
according to the selected light connector(s),
for control via
Note: The vehicle does not operate in the
BO power circuit when the 1st axle is lifted! The lift axle may only be used as a starting aid according to
Directive 97/27/EC!
Attention: reduced ground clearance in the area of the lift axle!
Through-loading height is limited by pallet stop
Cargo area width in the area of the pallet stop
reduced to: 2,460 mm i.L.
Supply and installation of a rear forklift bracket, suitable
for Palfinger piggyback forklifts (incl. forklift pockets, underrun protection according to ECE-R58 and 2 chain retainers for securing chains on the outside)
Tire size piggyback forklift max.: 23"
Type of mounting bracket: spar bracket
Dimensions of the mounting spars: 100 x 100 x 10 x 1500 mm
Dimensions of the forklift pockets: 200x100x5x1200 mm
Center distance of the forklift pockets: 380 mm
Width of the folded underrun protection: 1340 mm
Forklift pockets flush with the end crossmember at the rear.
Socket at the rear: 15-pin DIN ISO 12098
uneven load distribution!
Type: BO 13620
30 mm thick, waterproof floor panel, cut surfaces
sealed all around, surface, waterproof bonding
between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to max. 7,000 kg forklift axle load.
Diamond plate inserted in floor panel at the rear (4x450mm)
Type: AB 13620 AGG Dimensions 13,620 mm iL. x Width iL.
see posts
LM universal outer beams, continuous, for mounting
sliding tarpaulin and sliding posts
Edscha sliding roof (175) with plastic joints,
building height 175 mm, inclination 0 mm, designed for the
transport of grid boxes according to DIN 15155
Height i.L. lower edge of outer beam on the side at the front: 2,860 mm
Height i.L. lower edge of outer beam on the side at the rear: 2,860 mm
Height i.L. lower edge of transverse spar in the middle: 3,000 mm
Through-loading height in the rear portal: 2,845 mm
unladen overall vehicle height at the highest point approx. 4095 mm
hydraulic lift roof with 500 mm total lift,
can be raised separately on 4 corner posts
Structure height at the front can be lowered by 150 mm from the highest driving height (basic position) (in 50 mm increments), reduced roof lift: 350 mm
Structure height

Skelbimas buvo automatiškai išverstas. Galimos vertimo klaidos.