Žemagrindė platforma priekaba

SCHWARZMÜLLER Tiefladeanhänger mit 1tlg. Stahl-Rampen

You can find our complete vehicle inventory with vehicles available for immediate and short-term delivery on our website.
Excerpt from the equipment list.
Complete equipment available upon request.

Frame
* Steel welded construction with front frame curve and rear bevel
* Access ramp with excavator bucket recess in the center = recess in the rear between the longitudinal beams
* Approximately 2,300 mm long

Integrated into the outer frame
* 5 pairs of approximately 4-tonne lashing points (4 x in the low bed and 1 x on the raised platform)
* 7 pairs of recessed, pull-out approximately 10-tonne lashing rings (4 x in the low bed, 1 x in the access ramp, and 2 x on the raised platform)
* Standard ball-bearing swivel frame attachments
* Extendable widening elements on both sides of the low bed platform with softwood boards, approximately 50 mm thick
* (The track width of the construction machinery to be transported must not exceed the outer frame width of approximately 2,550 mm)
* 4 pairs of fold-up approximately 10-tonne lashing rings
* Arrangement: 1 pair at the front on the raised platform, inside the longitudinal beams
* 1 pair at the very back in the excavator bucket recess, left and right
* 1 pair at the front on the raised platform, in front of the curve, inside the longitudinal beams
* 1 pair in the low bed at the rear, in front of the access ramp, in the bucket recess on the left and right. Towing device
* Fixed drawbar with pivoting drawbar eye, approximately 40 + 50 mm, curved design, silent block mounting, drawbar retaining spring with tensioner
* Truck coupling height from approximately 840 mm to approximately 1,030 mm PP004059B Drawbar length approximately 1,800 mm Support system
* 2 automatic folding supports at the rear

Axles
* SAF air suspension low loader axles with drum brakes, load capacity 11 t/axle, S-cam brake approximately 300/200 mm, automatic brake linkage adjuster

Wheels
* 12 tires 235/75 R 17.5, 141J, manufacturer according to factory selection

Braking system/Suspension
* According to ECE regulation R13
* Dual-circuit compressed air braking system
* Braking system manufacturer Wabco, EBS system 4S3M, 1st and 2nd axles monitored RSS/RSP
* Stability program
* Spring-loaded parking brake on 2nd and 3rd axles
* Steel air tank
* Brake/air connection lines with 2 single coupling heads, yellow/red EBS/ABS connection cable
* Rubber band as a holder for EBS and electrical plugs
* Air suspension with raising and lowering device (only on rear axles), automatic adjustment of the driving level from 15 km/h (RTR), with axle stop on the front axle

Floor
* Softwood floor, approximately 50 mm thick, impregnated, protruding approximately 5 - 10 mm above the frame Steel tear plate cover over wheels

Ramps
* 2 foldable, one-piece, lightweight steel access ramps
* Length approximately 2,800 mm, width approximately 750 mm, with hardwood floor approximately 35 mm, impregnated
* Ramps can be shifted in width from an intermediate distance of approximately 350 mm to a maximum overall width of approximately 3,000 mm
* Ramps can be locked in the driving position by chains with tensioners
* Ramp lifting aid with coil spring
* Ramps can be shifted manually from the side with a rod
* Square ribs welded on the outside on the ramps and rear access ramp

Painting
* Steel granulate cleaning
* Hot-dip galvanizing
* Multi-layer epoxy zinc phosphate primer and spray painting with 2-component polyurethane
* Topcoat chassis = RAL 3002 carmine red
*
Fsdpfjz Ed Ausx Acgogi

Skelbimas buvo automatiškai išverstas. Galimos vertimo klaidos.