Priekaba su darbo platforma

MÜLLER-MITTELTAL 5 achs Tieflader, Nachlauflenkachse, MA liftbar

* T5 Profile 50.0:
* Wabco EBS (Electronic Braking System)
* TPMS (Tire Pressure Monitoring System)
* Emergency release device for spring brake cylinders
* Drum brakes
* 4 x 11 t Gigant axles
* Last axle with self-steering (locking the trailing axle for maneuvering purposes possible from the cab without the need for truck-side installation, and additionally via a switch on the trailer); lock must be disengaged before entering public roads
* Air suspension, lifting and lowering system with RtR valve
* 3rd axle liftable (ride height +30 mm when lifted)
* Forced relief and forced lowering of the lift axle for maneuvering purposes (requires truck-side installation) with speed-dependent switching via EBS electronics
* Smartboard as infotool with pressure sensors to display total axle load per axle group
* Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required)
* Mechanical signboard package for 3 m overall width
* Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment
* LED lighting system 12 / 24 V
* Removable LED beacon at rear
* Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, mounted left side
Iedexptn Dopfx Af Djtn
* Plastic front mudguards and galvanized steel rear mudguard aprons
* Turntable platform with 45° corners and 3 storage compartments with lockable hinged lids (hinges open to the rear)
* Reduction of low-loader platform by 500 mm to 6,280 mm including extended offset bend by 500 mm to the front
* Load securing package: 2 x 6.4 t lashing eyes at the front corners, 2 x 13.4 t UVV lashing eyes at each front and rear side corner, 5 x 10 t UVV lashing rings on each side (swiveling and lowerable, loadable in all directions), 4 stake pockets per side with 2 t lashing option, 1 x 16 t UVV lashing eye at rear cross member
* Rubber covering on the folding ramp, approach slope, and on the running surface of the low-loader platform
* Bamboo wood filler between side members before excavator stick support
* Extendable and folding outriggers for 3 m total width (plank holders under chassis, right side)
* Continuous excavator stick support with reinforcement profile from last axle to rear crossmember approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on sides of the excavator stick support
* Hydraulic folding ramp with dual-circuit hydraulics and deployable tip section approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side-shift
* Hydraulic rear support
* Hydraulic flow divider (for truck hydraulic pump output over 40 l/min up to max. 140 l/min)
* Loaded deck height 890 mm +/- 20 mm due to air suspension
* Deck above turntable: 2,600 + 390 x 2,520 mm
* Low-bed loading area: 6,280 + 500 x 2,520 mm, incl. 860 mm approach slope
* Chassis, turntable, drawbar, extension consoles, and access ramps hot-dip galvanized
* Drawbar, axles, hydraulic axle supports, and air tanks painted in black tone
* New vehicle with manufacturer's warranty
* Errors and prior sale excepted
* Available from week 14/2026

Skelbimas verčiamas automatiškai, todėl jame gali būtų vertimo klaidų.