Krano sunkvežimisVolvo
FH 540 8x2 Crane truck w/ 165 t/m HIDROKON crane w
Krano sunkvežimis
Volvo
FH 540 8x2 Crane truck w/ 165 t/m HIDROKON crane w
fiksuota kaina neįskaitant PVM
334 922 €
(418 652 € bruto)
Gamybos metai
2021
Sąlyga
Naudotas
Vieta
Sogn og Fjordane, Norway 

Rodyti vaizdus
Rodyti žemėlapį
Pagrindiniai duomenys
Kaina ir vieta
fiksuota kaina neįskaitant PVM
334 922 €
(418 652 € bruto)
- Vieta:
- Sogn og Fjordane
Skambinti
Techniniai duomenys
- Rida:
- 5 874 km
Pasiūlymo informacija
- Sąrašo ID:
- A191-80-271
- Nuorodos Nr.:
- 20511
- Naujinta paskutinį kartą:
- Data 2025.08.18
Aprašymas
Please provide reference number upon request: 20511
Specifications:
- 2021 model
- 5874 km (will increase slightly)
- Eu-approved until: 21.02.26
- Euro 6 engine
- 8x2
- 551 Hp
- Suspension on 1st and 2nd axle: Steel
- Suspension on 3rd and 4th axle: air
- 2 x 110 liter variable pumps
- 2 x manual extensions for main boom and 2 x for jib
- Scanreco optical remote control (Top model)
- Weight cell main boom
- Extra function for main boom and jib
- Auto leveling (The car puts itself in a level position ready for lifting.)
- Virtual room (Possibility to limit all axes with a few keystrokes, no need to go to a workshop for this. Brilliant when working under high voltage etc.)
- SKF central lubrication of the crown and up to the first joint
- Extra function fully extended on jib
- Single winch hook (Jib / main boom)
- 2-part winch hook (Jib / main boom)
- 4-part winch hook (Main boom)
- Hook for jib
- Hook for main boom (Large hook)
- Emergency lowering unit (24 volts)
- Wire stop sensor and sleeve
- 4 ton winch
- Diagnostic cable for online help (Remote help)
- Danfoss valve center
- 2 x 2 ton counterweight (Must only be used for cranes above the cabin otherwise the counterweights are not needed, and these can be removed as needed)
- Front support leg
Construction:
- 4 x work lights strategically placed inside each support leg cabinet.
- 50" LED bar work light rearward on the cabin
- Powerful LED lamps in the crane.
- VBG mount, with air servo control unit mounted in the rear cabinet left side.
- Bracket on the roof
- 2 pcs high beam LED bar on the roof forward (daylight!!).
- Orange work warning LED beam on the roof.
Kodpfxjwlm Dtj Af Djnc
- EasyUp foldable ladder in the side with railing.
- Boxes for chain, chainsaw etc. Mounted on the rear support leg so that these are driven out together with the support leg and are at the same time packed away while driving.
- Charger for control in the cabin
- Plastic internal screens axle 3 and 4.
- 3 edge pull-out cabinet between axle 3 and 4
- On the left side between axle 2 and 3 there is a large cabinet with 500 W fan heater installed to hang clothes to dry etc.
- Plane / bottom at the rear closed with alloxed aluminum floor plates that are cut to fit the car perfectly, with rounded edges for a very professional send.
- CNC manufactured plates up the rear edge of the cabin.
- Fully painted sides, cabin and stern.
- Resting cradle for crane for driving without jib.
- 5 support leg plates. 4 pcs 80x80x6 cm. placed in dedicated cradles at the rear on the "level"
- Right side large cabinet 1.2 x 1 meter
- Powerful LED back / work lights at the rear.
- Rear part of the car rebuilt with CNC manufactured plates, and beautiful LED taillights have been installed in several stages.
- Hatches strategically placed for access to relevant devices under the bodywork.
- Precisely cut out fields in the side coverage for access to the screen, manual controls, emergency lowering functions etc.
- Marker lights along the side mounted so that they flash together with the turn signals / direction indicators
- Cradle to hold the jib when not in use.
- Hydraulic extra function dismantled main boom and jib, but mounted if desired.
- Kettle in cabin
- Microwave oven in cabin
- Light...
Specifications:
- 2021 model
- 5874 km (will increase slightly)
- Eu-approved until: 21.02.26
- Euro 6 engine
- 8x2
- 551 Hp
- Suspension on 1st and 2nd axle: Steel
- Suspension on 3rd and 4th axle: air
- 2 x 110 liter variable pumps
- 2 x manual extensions for main boom and 2 x for jib
- Scanreco optical remote control (Top model)
- Weight cell main boom
- Extra function for main boom and jib
- Auto leveling (The car puts itself in a level position ready for lifting.)
- Virtual room (Possibility to limit all axes with a few keystrokes, no need to go to a workshop for this. Brilliant when working under high voltage etc.)
- SKF central lubrication of the crown and up to the first joint
- Extra function fully extended on jib
- Single winch hook (Jib / main boom)
- 2-part winch hook (Jib / main boom)
- 4-part winch hook (Main boom)
- Hook for jib
- Hook for main boom (Large hook)
- Emergency lowering unit (24 volts)
- Wire stop sensor and sleeve
- 4 ton winch
- Diagnostic cable for online help (Remote help)
- Danfoss valve center
- 2 x 2 ton counterweight (Must only be used for cranes above the cabin otherwise the counterweights are not needed, and these can be removed as needed)
- Front support leg
Construction:
- 4 x work lights strategically placed inside each support leg cabinet.
- 50" LED bar work light rearward on the cabin
- Powerful LED lamps in the crane.
- VBG mount, with air servo control unit mounted in the rear cabinet left side.
- Bracket on the roof
- 2 pcs high beam LED bar on the roof forward (daylight!!).
- Orange work warning LED beam on the roof.
Kodpfxjwlm Dtj Af Djnc
- EasyUp foldable ladder in the side with railing.
- Boxes for chain, chainsaw etc. Mounted on the rear support leg so that these are driven out together with the support leg and are at the same time packed away while driving.
- Charger for control in the cabin
- Plastic internal screens axle 3 and 4.
- 3 edge pull-out cabinet between axle 3 and 4
- On the left side between axle 2 and 3 there is a large cabinet with 500 W fan heater installed to hang clothes to dry etc.
- Plane / bottom at the rear closed with alloxed aluminum floor plates that are cut to fit the car perfectly, with rounded edges for a very professional send.
- CNC manufactured plates up the rear edge of the cabin.
- Fully painted sides, cabin and stern.
- Resting cradle for crane for driving without jib.
- 5 support leg plates. 4 pcs 80x80x6 cm. placed in dedicated cradles at the rear on the "level"
- Right side large cabinet 1.2 x 1 meter
- Powerful LED back / work lights at the rear.
- Rear part of the car rebuilt with CNC manufactured plates, and beautiful LED taillights have been installed in several stages.
- Hatches strategically placed for access to relevant devices under the bodywork.
- Precisely cut out fields in the side coverage for access to the screen, manual controls, emergency lowering functions etc.
- Marker lights along the side mounted so that they flash together with the turn signals / direction indicators
- Cradle to hold the jib when not in use.
- Hydraulic extra function dismantled main boom and jib, but mounted if desired.
- Kettle in cabin
- Microwave oven in cabin
- Light...
Tiekėjas
Pastaba: Užsiregistruokite nemokamai arba prisijunkite, kad gautumėte visą informaciją.
Registruota nuo: 2023
Pateikti užklausą
Telefonas & Faksas
+47 40 13... skelbimai
Jūsų skelbimas sėkmingai pašalintas
Įvyko klaida